In the traditional flow-resistance-differential (FRD) type valve-less piezoelectric pump, the generated outflow and pressure are discontinuous because of the inherent periodicity and fluctuation of the pump. To overcome these drawbacks, utilizing the bending vibration of piezoelectric bimorph to drive fluid was conducted. However, our investigation on the current status of this piezoelectric bimorph pump shows that larger driving force and vibration amplitude are required for fluid pumping; the pumping can be realized through the centrifugal force; and the mechanism of fluid pumping is no longer further studied. Based on these cases, the paper designed a piezoelectric-stack pump with variable-cross-section oscillating (VCSO) vibrator by imitating the swing of the caudal-fin of tuna, and the pump is neither the rotating type nor the volumetric type according to the taxonomy. The interaction between the oscillating vibrator and the fluid parcel is firstly analyzed from the viewpoint of momentum conservation, and the analytical expression of pump flow rate is obtained. Then the modal and harmonic response analyses on the vibrator immerged in water are carried out. From the analyses the first two orders resonance frequencies are 832 Hz and 1 939 Hz, respectively, and the peak value of the tip amplitude is 0.6 mm. Laser Doppler vibrometer is used to measure both the frequency and vibration amplitude, and the determined first two orders resonance frequencies are 617 Hz and 1 356 Hz, respectively. The measured tip amplitude reaches to the peak value of 0.3 mm. At last, experimental measurement for the flow rates with different driving frequencies is conducted. The results show that the flow rate can reach 560 mL/min at 1 370 Hz when the pump runs under the backpressure of 30 mm water column. And the flow rate is as much as 560% of that of experiment results carried out by researchers from Brazil. The proposed pump innovates in both theory and taxonomy; in addition, the pump overcomes the drawbacks such as large flow flu
HU XiaoqiZHANG JianhuiHUANG YiXIA QixiaoHUANG WeiqingZHAO Chunsheng
The valveless piezoelectric pump integrates driving and transmitting into one operating element,and characterizes easy micro-miniaturization.But,there is the original sin of low pressure and low flow.Thus,it must avoid weakness to choose applications field.This paper analyzes the flow characteristics in the rotary spiral-tube,which will cause the Coriolis force,and subsequently influence the fluid moving.The principle of the pump is deduced,and the spiral-tube-type valveless piezoelectric pump is invented.The angular velocity variation can be obtained when the pump attitude changes,which theoretically verifies the gyroscopic effect of the pump.A pump is fabricated for experimental testing.Experiments has shown that when Archimedes spiral h?4p is selected for the tube design,and the rotation speed of the plate is 70 r/min,the pressure differential is 9 mm H2O,which is 1.5 times that of 0 r/min rotation speed.If introduced the low-cost and miniaturized gyroscope,then this may promise potential application in these areas such as smart cars,robots,and home health care.
A valveless piezoelectric pump with rotatable unsymmetrical slopes is developed in this research.It has the following features:The pump integrates driving and transporting,and it can mix different fluids while transporting them.In this paper,firstly,the design of the valveless piezoelectric pump with rotatable unsymmetrical slopes was proposed,and the single-direction flow principle was explained.Then,the fluid mechanics model of the valveless piezoelectric pump with rotatable unsymmetrical slopes was established.Meanwhile,the numerical simulation of the pump was performed.Finally,the experiments on relationship between the rotation angles of the slope and the flow rates were conducted.The experimental results showed that the maximum flow was 32.32 mL min 1.The maximum relative error between the theoretical results and the experimental ones was 14.59%.For the relationship between rotation angles and flow ratio of two inlets,the relative error between the experimental and theoretical maxima was 3.75%.Thus,the experiments proved the feasibility of the pump design and verified the theory.
In recent years, the research and development of piezoelectric pumps have become an increasingly popular topic. Minimization, structure simplification and stronger output become the focus of piezoelectric pumps’ research due to its possible application in MEMS technology. The valveless fishtailing piezoelectric pump, neither a volumetric nor a rotating pump, was invented according to the bionics of fish swimming. With assumption that the head of the fish is fixed while its tail is swinging, fluid would flow toward the end of the tail, achieving the function of a valveless pump. This type of pumps creates a new branch for the piezoelectric pump research, which is proposed for the first time in this paper. The relationship between the flow rates and vibrating frequencies was derived from the interaction between the vibrator and fluid. Numerical simulations with FEM software were conducted to study the first and second vibration modes of the piezoelectric vibrator. The results showed that the maximum amplitude of the vibrator was 0.9 mm at the frequency of 76 Hz for the first vibration mode, while the maximum amplitude of the vibrator was 0.22 mm at the frequency of 781 Hz for the second vibration mode. Experiments were conducted with the Doppler laser vibration measurement system, and the results were compared to those of the FEM simulation. It was shown that in the first vibration mode the piezoelectric vibrator reached its maximum amplitude of about 0.9 mm at the driving frequency of 49 Hz, which gives the flow rate of 2.0 mL/min, in the second vibration mode, the maximum amplitude was about 0.25 mm at the frequency of 460 Hz with the flow rate being 6.4 mL/min.
HUANG Yi1, ZHANG JianHui1, HU XiaoQi1, XIA QiXiao2, HUANG WeiQing1 & ZHAO ChunSheng1 1 Department of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
Typically,liquid pump and liquids mixer are two separate devices.The invention of piezoelectric pump makes it possible to integrate the two devices.Hower,the existing piezoelectric mixing-pumps are larger because the need the space outside the chamber,and another shortcome of them is that they cannot adjust the mixing ratio of two liquids.In this paper,a new piezoelectric pump being capable of integrating mixer and pump is presented,based on the theory of the piezoelectric pump with the unsymmetrical slopes element（USE）.Besides the features of two inlets and one outlet,the piezoelectric pump has a rotatable unsymmetrical slopes element（RUSE）.When the pump works,two fluids flow into the inlet channels respectively.Then the RUSE controls the ratio of the two flows by adjusting the flow resistances of the two inlet channels.The fluids form a net flow due to the USE principle,while they are mixed into a homogeneous solution due to strong turbulence flow field and complex vortices generated by RUSE in the chamber.And then the solution flows through the outlet.Firstly,the theoretical analysis on this pump is performed.Meanwhile,the flow field in the chamber is calculated and simulated.And then,the relationship between the flows of the two channels and the rotating angle of the RUSE is set up and analyzed.Finally,experiment with the proposed pump is carried out to verify the numerical results.A RUSE with 20° slope angle is used in the experiment.Four sets of data are tested with the RUSE at the rotating angles of 0°,6°,11°,and 16°,respectively,corresponding to the numerical models.The experimental results show that the empirical data and the theoretical data share the same trend.The maximum error between the theoretical flow and the experimental flow is 11.14%,and the maximum error between the theoretical flow ratio of the two inlets and the experimental one is 2.5%.The experiment verified the theoretical analysis.The proposed research provides a new idea for integration of micro liquids mixer and micro liq
Among most traditional piezo water cooling systems, piezoelectric valve pumps are adopted as their driving sources. The valves in these pumps induce problems of shock and vibration and also make their structure complicated, which is uneasy to minimize and reduce their reliability and applicability of the whole system. In order to avoid these problems caused by valve structure, a novel valveless piezoelectric pump is developed, which integrates both functions of transforming and cooling. The pump’s Y-shape tree-like construction not only increases the efficiency of cooling but also the system reliability and applicability. Firstly, a multistage Y-shape treelike bifurcate tube is proposed, then a valveless piezoelectric pump with multistage Y-shape treelike bifurcate tubes is designed and its working principle is analyzed. Then, the theoretical analysis of flow resistance characteristics and the flow rate of the valveless piezoelectric pump are performed. Meanwhile, commercial software CFX is employed to perform the numerical simulation for the pump. Finally, this valveless piezoelectric pump is fabricated, the relationship between the flow rates and driving frequency, as well as the relationship between the back pressure and the driving frequency are experimentally investigated. The experimental results show that the maximum flow rate is 35.6 mL/min under 100 V peak-to-peak voltage (10.3 Hz) power supply, and the maximum back pressure is 55 mm H2O under 100 V (9 Hz) power supply, which validates the feasibility of the valveless piezoelectric pump with multistage Y-shape treelike bifurcate tubes. The proposed research provides certain references for the design of valveless piezoelectric pump and improves the reliability of piezo water cooling systems.
