In this review, acritical look at the research progress ofexperimentalsolid mechanics in China for the past years is presented. Issues are discussed of the discovery and development of new fundamental methods and techniques versus performance benchmarking for many of their applications. Included herein are photoelasticity and various forms of modern photomechanics, acoustical techniques, image processing and videometrics, radial and spectrum techniques, and experimental mechanics on micro/nano scale. It is also noticed that both the ever developed instrumentation and specialized synthetical techniques have played important roles in advancing experimental mechanics in scientific researches and industrial applications. Finally, an attempt is made to look into the future of experimental solid mechanics with personal opinions offered on what the future trends will be for the researches in the field.
Optical full-field measurement methods are now widely applied in various domains. In general,the displacement fields can be directly obtained from the measurement,however in mechanical analysis strain fields are preferred.To extract strain fields from noisy displacement fields is always a challenging topic.In this study,a finite element method for smoothing displacement fields and calculating strain fields is proposed.An experimental test case on a holed aluminum specimen under tension is applied to validate this method.The heterogeneous displacement fields are measured by digital image correlation(DIC).By this proposed method,the result shows that the measuring noise on experimental displacement fields can be successfully removed,and strain fields can be reconstructed in the arbitrary area.
B.Q.Guo,~(1,a)) H.M.Xie,~(1,b)) Y.J.Li,~1P.W.Chen,~2and Q.M.Zhang~2 1) AML,Department of Engineering Mechanics,Tsinghua University,Beijing 100084,China 2) State Key Laboratory of Explosion Science and Technology,Beijing Institute of Technology,Beijing 100081, China
This paper explores the planar arrangement feature of the copper interconnects in a view field of several millimeters by the focused ion-beam （FIB） Moire inversion method quantitatively. The curved FIB Moire patterns indicate that the copper interconnects are a series of curves with continuous variations instead of beelines. The control equation set of the copper interconnects central lines is attained through the Moire inversion method. This work can be extended to inspect the structural defects and provide a reliable support for the interconnects structure fabrication.
Qinghua WangSatoshi KishimotoHuimin XieKewei XuJianfeng Wang
This paper investigates an advanced grating-transferring technique combined with geometric phase analysis (GPA) for residual strain evaluation of curved surface.A standard holographic grating is first transferred to a pre-produced epoxy resin film and then consolidated to a test region of curved surface.With a rubber mold and silicone rubber the deformed grating is replicated to a sheet metal after hole-drilling for release of residual stress.After that the grating is transferred from the sheet metal to the glass plate,which would be served as an analyzer grating (specimen grating).By GPA the local strain distributions related to the phase difference between the reference grating and analyzer grating for the released stress can be evaluated.A validation test has been conducted on the weld joint of a stainless steel tube and the obtained results demonstrate the ability of the method in measuring the residual strain of curved surface.
Zhanwei Liu,1,Jiangfan Zhou,1 Xianfu Huang,1 Jian Lu,2 and Huimin Xie 3,1) Department of Mechanics,School of Astronautics,Beijing Institute of Technology,Beijing 100081,China 2) Department of Mechanical Engineering,The Hong Kong Polytechnic University,Hong Kong,China 3) AML,Department of Engineering Mechanics,Tsinghua University,Beijing 100084,China
The shear modulus of the adhesive layer and the failure mode of adhesive structure on single lap joint specimens under tensile tests are investigated in this paper.The aluminum-aluminum adherends are bonded by two different adhesives:polydimethylsiloxane (PDMS) and epoxy.The full deformation fields are measured using the digital image correlation (DIC) method with the images on the middle part of the adhesive layer recorded by a high resolution microscope.Then,the shear modulus values of the two adhesives are calculated with a simple pure shear strain model.A numerical model is proposed to simulate the single lap joint structure under tensile load in comparison with the experimental results.The results show that this method can successfully estimate the shear modulus of the adhesive layer.The failure behavior of epoxy adhesive/adherend interface is also analyzed and discussed.
The cross-section profiles of polymer deformation in the hot embossing lithography process were studied by finite element method for various temperature, time and pressure. In order to successfully fabricate high-frequency grating lines, an optimal imprint condition was selected and the related experiments were carried out. The fabricated gratings were illuminated by the SEM image and AFM analysis, which agree well with the simulated results. Therefore, the finite element methods are helpful for a better comprehension of the polymer flow phenomena governing the pattern definition and the design of optimum processing conditions for successful grating fabrication.
